Origami Fish

By Dallin -
This fish model was designed by Michael LaFosse. It is a rather tricky model that requires several difficult folds, but it is not hard to fold after some practice. 


Step 1: Fold a fish base


Step 2: Mountain fold the far left point behind to the right


Step 3: Valley fold the left hand flaps to the right...

 ...like so:

Step 4: Mountain fold the model in half


Step 5: Flip the model over so the right becomes the left


Step 6: Valley fold the top right corner down so it meets the nearest edge


Step 7: Valley fold the bottom right corner up so it is a little past the edge of the flap you folded in step 6


Step 8: Flip the model back over


Step 9: Valley fold the bottom left corner up so the bottom edge lines up on both sides


Step 10: Flip the model over again


Step 11: Valley fold point A (marked in the above pic) up so it is in the middle of the flap



Step 12: Valley fold most of the bottom edge up



Step 13: Crease and unfold


Step 14: Reverse fold the flap up


Step 15: At the tip of the tail there are two separate flaps. Pull the inside flap down to complete the tail.


Step 16: Pull down the fin at the front of the fish to complete your fish!


Comments

Post a Comment

Popular posts from this blog

Origami Dragon (harder)

By Dallin -
Image
The dragon is my favorite origami model but it is definitely not a beginner model. To fold it, you need to be able to petal, squash, sink, valley, and reverse fold. If you can't do all of  these folds, refer to the  folds  post. Step 1: Fold a  bird base  and have the separate points at the bottom Step 2: Valley fold the top point down Step 3: Mountain fold the top point down around the back Step 4: Valley fold the top point to the middle crease line, crease, and unfold Step 5: Now open the paper and sink fold the tip down. You will see a small square in the middle... ... and pinch the edges a little to define them... ...now press the center point down to 'sink' it It should look like this: Step 6: Valley fold the top layer on the right to the left Step 7: Valley fold the bottom point up Step 8: Valley fold point A to point B (refer to pic above) Step 9: Repeat steps
Read more

Origami Basketball Hoop

By Dallin -
Image
The basketball hoop is a fun and interactive model. Once made, just crumple some paper into a ball and start shooting (you can also make a crumpled ball ). It can be made from either origami paper or printer paper. If you make it from origami paper, it won't be as tall, and won't stand up as easily, but it will still work. I would recommend making it from printer paper though. Also, it might fall over when being used, so just put a book or something behind it and it will stay up fine. Step 1: If you're using printer paper, orient it vertically. If you're using origami paper, make a  waterbomb base  and then skip to step 9. Step 2: Valley fold the top left corner over (the top edge should align with the right side) Step 3: Unfold Step 4: Valley fold the top right corner over to the left edge Step 5: Unfold and turn the paper over Step 6: After you've turned the paper over, fold the top edge down so the creases lie on t
Read more

Oragami Inflatable Frog

By Dallin -
Image
The inflatable frog is a traditional Japanese origami model. It is a rather common model, but it's only one of many origami frogs out there. It is a rather advanced model, requiring squash and petal folds to make the base, and reverse folds to form the frog. It inflates, but is folded from a frog base rather than a waterbomb base. Step 1: Fold a  frog base Step 2: Valley fold the bottom right and left edges to the center Step 3: Repeat step 2 on the other three parts of the frog base  Step 4: Valley fold the top layer of the bottom two points up Step 5: Crease and unfold Step 6: Inside reverse fold the flaps up Step 7: Valley fold the two bottom points remaining out to their respective sides Step 8: Crease and unfold Step 9: Inside reverse fold the flaps Step 10: Now make reverse folds to form the arms and legs (use the picture below to know where to make your folds) Step 11: Blow into the litt
Read more