The Box

By Dallin -
The box is an easy origami model and is a variation of the standing container . You can see the similarities between the box and the container, but the box is slightly easier. The first ten or so steps are identical, so learning one will help you learn the other.


Step 1: Fold a blintz base


Step 2: Valley fold the top left corner to the bottom right


Step 3: Unfold and valley fold the top right corner to the bottom left



Step 4: Unfold and mountain fold the model in half 


Step 5: Unfold and mountain fold it in half along the vertical crease



Step 6: Unfold and turn over

 Orient your paper like this:

Step 7: Now collapse the paper like a square base, bringing the left and right corner to meet at the bottom, and then flatten the top flap



Step 8: Valley fold the top layer of the bottom point to the top and unfold



Step 9: Pry open the flaps on either side of the center and squash fold the flap up




Step 10: Turn over and repeat steps 8 and 9 on this side...

 ...so it looks like this

Step 11: Valley fold the top layer on the left side to the right


Step 12: Turn the model over and valley fold the top layer on the left to the right

It will look like this on both sides:

Step 13: Valley fold the two far edges to the center


Step 14: Turn over and valley fold the two far edges to the center



Step 15: Valley fold the bottom point to the top


Step 16: Turn the model over so the bottom becomes the top 

Step 17: Now valley fold the top point to the bottom


Step 18: Unfold the last two flaps slightly, and then pull them gently apart

 Use your finger to press in the bottom to flatten the bottom of the box...
 ...so it looks like this:

Your box is now complete!


If you would like to make the side flaps smaller, turn the model upside down and valley fold the far points in



It will look like this:


Comments

Post a Comment

Popular posts from this blog

Origami Dragon (harder)

By Dallin -
Image
The dragon is my favorite origami model but it is definitely not a beginner model. To fold it, you need to be able to petal, squash, sink, valley, and reverse fold. If you can't do all of  these folds, refer to the  folds  post. Step 1: Fold a  bird base  and have the separate points at the bottom Step 2: Valley fold the top point down Step 3: Mountain fold the top point down around the back Step 4: Valley fold the top point to the middle crease line, crease, and unfold Step 5: Now open the paper and sink fold the tip down. You will see a small square in the middle... ... and pinch the edges a little to define them... ...now press the center point down to 'sink' it It should look like this: Step 6: Valley fold the top layer on the right to the left Step 7: Valley fold the bottom point up Step 8: Valley fold point A to point B (refer to pic above) Step 9: Repeat steps
Read more

Origami Basketball Hoop

By Dallin -
Image
The basketball hoop is a fun and interactive model. Once made, just crumple some paper into a ball and start shooting (you can also make a crumpled ball ). It can be made from either origami paper or printer paper. If you make it from origami paper, it won't be as tall, and won't stand up as easily, but it will still work. I would recommend making it from printer paper though. Also, it might fall over when being used, so just put a book or something behind it and it will stay up fine. Step 1: If you're using printer paper, orient it vertically. If you're using origami paper, make a  waterbomb base  and then skip to step 9. Step 2: Valley fold the top left corner over (the top edge should align with the right side) Step 3: Unfold Step 4: Valley fold the top right corner over to the left edge Step 5: Unfold and turn the paper over Step 6: After you've turned the paper over, fold the top edge down so the creases lie on t
Read more

Oragami Inflatable Frog

By Dallin -
Image
The inflatable frog is a traditional Japanese origami model. It is a rather common model, but it's only one of many origami frogs out there. It is a rather advanced model, requiring squash and petal folds to make the base, and reverse folds to form the frog. It inflates, but is folded from a frog base rather than a waterbomb base. Step 1: Fold a  frog base Step 2: Valley fold the bottom right and left edges to the center Step 3: Repeat step 2 on the other three parts of the frog base  Step 4: Valley fold the top layer of the bottom two points up Step 5: Crease and unfold Step 6: Inside reverse fold the flaps up Step 7: Valley fold the two bottom points remaining out to their respective sides Step 8: Crease and unfold Step 9: Inside reverse fold the flaps Step 10: Now make reverse folds to form the arms and legs (use the picture below to know where to make your folds) Step 11: Blow into the litt
Read more