Oragami Inflatable Fish

By Dallin -
The inflatable fish is a neat little model that, as the name suggests, inflates. It is folded from the waterbomb base, and is similar to other models folded from the waterbomb base (such as the waterbomb, cube, and inflatable bunny). The paper I used was purple, but my camera was having light issues, so it looks blue.


Step 1: Fold a waterbomb base and orient it as shown below


Step 2: Valley fold the left corner to the top


Step 3: Valley fold the right corner to the top


Step 4: Take the left side of the newly formed flap and valley fold it to the center


Step 5: Valley fold the right side to the center as well


Step 6: Take the top two corners and valley fold them down so the edges meet the edges of the flaps folded in steps 4 and 5



Step 7: Valley fold the flaps you folded in step 6 down over the flaps folded in steps 4 and 5



Step 8: Unfold the folds you made in step 8


Step 9: Open the flap and stick the triangular flaps inside (this is exactly the same steps as in the waterbomb and inflatable bunny). Do the same thing on the right and left flaps.




Step 10: Turn the model over


Step 11: Valley fold the top left edge to the center


Step 12: Valley fold the top right edge to the center


Step 13: Valley fold the bottom left corner to the outside like so:


Step 14: Valley fold the far left point to the right, folding the rest of the flap as well


Step 15: To inflate, blow into the little hole indicated by my index finger in the picture. This is the trickiest part, and you might have to move the tail fin a little to get a good blow.


Your inflatable fish is now complete!


Comments

Post a Comment

Popular posts from this blog

Origami Dragon (harder)

By Dallin -
Image
The dragon is my favorite origami model but it is definitely not a beginner model. To fold it, you need to be able to petal, squash, sink, valley, and reverse fold. If you can't do all of  these folds, refer to the  folds  post. Step 1: Fold a  bird base  and have the separate points at the bottom Step 2: Valley fold the top point down Step 3: Mountain fold the top point down around the back Step 4: Valley fold the top point to the middle crease line, crease, and unfold Step 5: Now open the paper and sink fold the tip down. You will see a small square in the middle... ... and pinch the edges a little to define them... ...now press the center point down to 'sink' it It should look like this: Step 6: Valley fold the top layer on the right to the left Step 7: Valley fold the bottom point up Step 8: Valley fold point A to point B (refer to pic above) Step 9: Repeat steps
Read more

Origami Basketball Hoop

By Dallin -
Image
The basketball hoop is a fun and interactive model. Once made, just crumple some paper into a ball and start shooting (you can also make a crumpled ball ). It can be made from either origami paper or printer paper. If you make it from origami paper, it won't be as tall, and won't stand up as easily, but it will still work. I would recommend making it from printer paper though. Also, it might fall over when being used, so just put a book or something behind it and it will stay up fine. Step 1: If you're using printer paper, orient it vertically. If you're using origami paper, make a  waterbomb base  and then skip to step 9. Step 2: Valley fold the top left corner over (the top edge should align with the right side) Step 3: Unfold Step 4: Valley fold the top right corner over to the left edge Step 5: Unfold and turn the paper over Step 6: After you've turned the paper over, fold the top edge down so the creases lie on t
Read more

Oragami Inflatable Frog

By Dallin -
Image
The inflatable frog is a traditional Japanese origami model. It is a rather common model, but it's only one of many origami frogs out there. It is a rather advanced model, requiring squash and petal folds to make the base, and reverse folds to form the frog. It inflates, but is folded from a frog base rather than a waterbomb base. Step 1: Fold a  frog base Step 2: Valley fold the bottom right and left edges to the center Step 3: Repeat step 2 on the other three parts of the frog base  Step 4: Valley fold the top layer of the bottom two points up Step 5: Crease and unfold Step 6: Inside reverse fold the flaps up Step 7: Valley fold the two bottom points remaining out to their respective sides Step 8: Crease and unfold Step 9: Inside reverse fold the flaps Step 10: Now make reverse folds to form the arms and legs (use the picture below to know where to make your folds) Step 11: Blow into the litt
Read more