The Fancy Box

By Dallin -
The fancy box is a rather easy model to fold, consisting of only valley and mountain folds. The final product is a box that isn't as practical as other boxes, but looks much more decorative.


Step 1: Fold a blintz base


Step 2: Turn the model over


Step 3: Valley fold all corners to the center


Step 4: Fold each corner out to the edge of the model...

... like this:

Step 5: Turn the model over again


Step 6: (working with just the top left flap) Mountain fold the point in the center to the top left corner


Step 7: Valley fold the flap back, but not all the way


Step 8: Continue to pleat fold the flap until the tip lines up with the edge...


... like this

Step 9: Repeat steps 6-8 on the remaining three flaps


Step 10: To transform your box, put a finger into each of the corners and open up the interior so it expands into a box



Step 11: Add candy

Your fancy box is now complete!


Comments

Post a Comment

Popular posts from this blog

Origami Dragon (harder)

By Dallin -
Image
The dragon is my favorite origami model but it is definitely not a beginner model. To fold it, you need to be able to petal, squash, sink, valley, and reverse fold. If you can't do all of  these folds, refer to the  folds  post. Step 1: Fold a  bird base  and have the separate points at the bottom Step 2: Valley fold the top point down Step 3: Mountain fold the top point down around the back Step 4: Valley fold the top point to the middle crease line, crease, and unfold Step 5: Now open the paper and sink fold the tip down. You will see a small square in the middle... ... and pinch the edges a little to define them... ...now press the center point down to 'sink' it It should look like this: Step 6: Valley fold the top layer on the right to the left Step 7: Valley fold the bottom point up Step 8: Valley fold point A to point B (refer to pic above) Step 9: Repeat steps
Read more

Origami Basketball Hoop

By Dallin -
Image
The basketball hoop is a fun and interactive model. Once made, just crumple some paper into a ball and start shooting (you can also make a crumpled ball ). It can be made from either origami paper or printer paper. If you make it from origami paper, it won't be as tall, and won't stand up as easily, but it will still work. I would recommend making it from printer paper though. Also, it might fall over when being used, so just put a book or something behind it and it will stay up fine. Step 1: If you're using printer paper, orient it vertically. If you're using origami paper, make a  waterbomb base  and then skip to step 9. Step 2: Valley fold the top left corner over (the top edge should align with the right side) Step 3: Unfold Step 4: Valley fold the top right corner over to the left edge Step 5: Unfold and turn the paper over Step 6: After you've turned the paper over, fold the top edge down so the creases lie on t
Read more

Oragami Inflatable Frog

By Dallin -
Image
The inflatable frog is a traditional Japanese origami model. It is a rather common model, but it's only one of many origami frogs out there. It is a rather advanced model, requiring squash and petal folds to make the base, and reverse folds to form the frog. It inflates, but is folded from a frog base rather than a waterbomb base. Step 1: Fold a  frog base Step 2: Valley fold the bottom right and left edges to the center Step 3: Repeat step 2 on the other three parts of the frog base  Step 4: Valley fold the top layer of the bottom two points up Step 5: Crease and unfold Step 6: Inside reverse fold the flaps up Step 7: Valley fold the two bottom points remaining out to their respective sides Step 8: Crease and unfold Step 9: Inside reverse fold the flaps Step 10: Now make reverse folds to form the arms and legs (use the picture below to know where to make your folds) Step 11: Blow into the litt
Read more