How to Make an Origami Beach Umbrella (With NO scissors, glue, OR tape)

By -



     I've been wanting to post something summer-themed, because I am in the middle of summer myself. One of the first things that came into my head to do was a beach umbrella. When searching online, the only origami beach umbrellas that I could find used tape, scissors, and/or glue! Personally, I believe that paper should be the only supply used in origami. 
     So, I adapted what I found online, to use paper and nothing else.  Just folding, no cutting and no taping. And that it what you will find in this post. And FYI: You will need 2 pieces of paper for this. If you want the pole to be shorter than mine was, used a smaller piece of paper than the top. 
     If you are confused on a fold, just go to my page on folds.

      
Lets begin:
Step 1: Begin by making a Waterbomb Base with one of your papers. (This will become the top of your umbrella.) Set the other paper aside for later.

  


Step 2: Take the top flap on the right side and perform a squash fold down the center. (Crease it, despite what the picture looks like)




Step 3: Valley fold the left half of your squash fold to the right half. (Back to its original side)

Step 4: Repeat steps 2 and 3 on the left side.



*Missing picture of folding it back to its original side*

Step 5: Flip your paper over and repeats steps 2 and 3 twice more, using the remaining two flaps.


Oh, and sorry that the next two pictures are a little wonky. 


This is how it should look right now.

Step 6: Fold the first right flap to the left one time. Now you should see color, no white. 

Step 7: Valley fold the top flap of the bottom as far as it can go. Crease and then unfold.

Step 8: Now you want to fold it in the opposite direction and tuck it into the middle of your model. 



Step 9: Repeat steps 6 through 8 three more times.

*MORE MISSING PICTURES, SORRY*

When you let your paper unfold, it should look like this. The top of your umbrella is complete!

Step 10: Start with your second paper patterned/colored side down.

Step 11: Starting on one side, tightly roll up your paper. Note: This is when most instructions tell you to glue. If you want, go right ahead. 

I rolled mine a few times before it could stand up on its own. However, it's not a good idea to let go or else it will expand uncontrollably. 

Step 12: If you look at the top of your umbrella, you might have a little hole. Push your pole through this hole. Try to keep the hole as small as possible, to prevent your pole from expanding. I personally made mine too wide. If needed, use a pencil to widen the hole for you a bit. 

Step 13: Adjust positioning of both pieces to your liking and then you have your finished beach umbrella!


And there you go! Hopefully the instructions were clear and you weren't lost. If you need clarification feel free to just comment down below and I'll try to address the issue as soon as possible.
Also, please let me know if you're interesting in more summer and/or season themed origami instructions.

Happy Folding!

Comments

Post a Comment

Popular posts from this blog

Origami Basketball Hoop

By Dallin -
Image
The basketball hoop is a fun and interactive model. Once made, just crumple some paper into a ball and start shooting (you can also make a crumpled ball ). It can be made from either origami paper or printer paper. If you make it from origami paper, it won't be as tall, and won't stand up as easily, but it will still work. I would recommend making it from printer paper though. Also, it might fall over when being used, so just put a book or something behind it and it will stay up fine. Step 1: If you're using printer paper, orient it vertically. If you're using origami paper, make a  waterbomb base  and then skip to step 9. Step 2: Valley fold the top left corner over (the top edge should align with the right side) Step 3: Unfold Step 4: Valley fold the top right corner over to the left edge Step 5: Unfold and turn the paper over Step 6: After you've turned the paper over, fold the top edge down so the creases lie on t
Read more

Origami Dragon (harder)

By Dallin -
Image
The dragon is my favorite origami model but it is definitely not a beginner model. To fold it, you need to be able to petal, squash, sink, valley, and reverse fold. If you can't do all of  these folds, refer to the  folds  post. Step 1: Fold a  bird base  and have the separate points at the bottom Step 2: Valley fold the top point down Step 3: Mountain fold the top point down around the back Step 4: Valley fold the top point to the middle crease line, crease, and unfold Step 5: Now open the paper and sink fold the tip down. You will see a small square in the middle... ... and pinch the edges a little to define them... ...now press the center point down to 'sink' it It should look like this: Step 6: Valley fold the top layer on the right to the left Step 7: Valley fold the bottom point up Step 8: Valley fold point A to point B (refer to pic above) Step 9: Repeat steps
Read more

Oragami Inflatable Frog

By Dallin -
Image
The inflatable frog is a traditional Japanese origami model. It is a rather common model, but it's only one of many origami frogs out there. It is a rather advanced model, requiring squash and petal folds to make the base, and reverse folds to form the frog. It inflates, but is folded from a frog base rather than a waterbomb base. Step 1: Fold a  frog base Step 2: Valley fold the bottom right and left edges to the center Step 3: Repeat step 2 on the other three parts of the frog base  Step 4: Valley fold the top layer of the bottom two points up Step 5: Crease and unfold Step 6: Inside reverse fold the flaps up Step 7: Valley fold the two bottom points remaining out to their respective sides Step 8: Crease and unfold Step 9: Inside reverse fold the flaps Step 10: Now make reverse folds to form the arms and legs (use the picture below to know where to make your folds) Step 11: Blow into the litt
Read more